Should we keep showing the banner you just clicked on?
Learn More about this warning
The following item(s) have been added to your cart...You can now continue shopping or go
straight to checkout
The fixture is mounted off the floor and is plumbed for a wall waste outlet. Wash fountains with this option include a grid strainer and tail piece.
The fixture is mounted on the floor and is plumbed for a wall waste outlet. Wash fountains with this option include a grid strainer and tail piece.
This option provides a 4 inch (101.6 mm) centerset, chrome-plated brass gooseneck spout with wrist blade handles and is furnished with mounting collars and nuts. The faucet includes an aerator restricting the flow to a maximum 1.5 gallon (5.7 lters) per minute.
This option includes and individual pushbutton control for the Air-Control™ Metering valve and is provided standard with a hot and cold pressure balancing mixing valve. Water flow metering can be field set for range from 5 to 60 seconds. Pushbutton requires less than 5 pounds of pressure to activate the valve. See individual model specification sheets for pushbutton location.
9VDC Programmable Piezo button(s) with 10’ foot connection leads are operated by touching piezo cap to activate solenoid valve. Button(s) have a default 8 second metered flow, but can be programed for additional time on site. Flow cycle can be stopped by touching the Piezo cap before the flow cycle ends. Button(s) are powered by 9VDC transformer or optional 6 AA battery pack (Batteries Not Included).
Use of this option provides "Hands-Free" washing. It includes an infra-red sensor operated, solenoid water valve, mixing valve and a transformer. A 24VAC sensor is used on our Wash-Ware product lines whenever the -SO option is selected. This sensor operates with a 30 second metered flow or cycle once an object is detected before turning off the solenoid valve.
In addition to saving installation costs, this option is ideal for renovation projects where hands-free control is desired. Use of this option eliminates the requirement to provide electrical power and wiring for units with -SO Sensor Operated Control. Each sensor and solenoid valve is powered by a concealed battery pack with 6 AA batteries (batteries provided by the installer and not included). We recommend using Lithium or Alkaline batteries to power the sensor.The -SO-BAT Sensor activates the solenoid valve whenever an object is detected in the range area. The sensor will keep the solenoid open, allowing water to flow until the object is removed from sensor range. If an object is positioned in a manner that it is under constant detection the sensor will turn the solenoid off after 30-90 seconds.
This option provides a stainless steel tubular spout. "J" Spout is deck mounted and is designed to allow ample space for hands.
This option provides a stainless steel tubular spout. "L" Spout is deck mounted and extends over bowl to utilize entire basin.
This option positions Air-Control™ Metering valve pushbutton on stainless steel countertop and is offered as an alternative to the standard backsplash mounted pushbutton. May not be available with selection of other combinations.
This option provides a removable stainless steel enclosure to completely conceal drain waste fitting, supply and waste connections, and under basin(s). Works in conjunction with standard stainless steel trap enclosure to fully conceal bottom of unit. (Not available with -SSN 2-1/2" High Narrow Skirt.)
This option provides additional countertop space to the LEFT side of the basin. This counter space may be used to offset a basin from an adjacent side wall or as a toiletry shelf. See individual specification sheets for extended lengths. Note:3770-3773 Series are provided with an open end standard.
This option provides additional countertop space to the RIGHT side of the basin. This counter space may be used to offset a basin from an adjacent side wall or as a toiletry shelf. See individual specification sheets for extended lengths. Note:3770-3773 Series are provided with an open end standard.
Click Enviro-Glaze's® colors below to view in detail!
Why use Enviro-Glaze®?
Acorn Engineering Company has developed a color coating system which will allow you to purchase durable stainless steel fixtures in designer colors. Enviro-Glaze® is a superior finish which gives you a colorful and functional alternative to a stainless steel finish.
What is Enviro-Glaze®?
Enviro-Glaze® is a smooth or textured hard coating that endures impact, will not bubble, and is chip-resistant. The coating is an electrostatically sprayed powder that is applied to the outsideof the stainless steel fixture, then cured at a temperature in excess of 400°F. Vigorous inspectionduring every step of the production process ensures that the finish on every fixture meets Acorn’s high quality standards.
How should Enviro-Glaze® be cleaned and maintained?
Acorn’s Enviro-Glaze® finish creates a beautiful surface that is easily cleaned, maintained andkept in a sanitary condition. A solution of warm water and mild soap is all that is necessary forcleaning the unit.*
* Long exposure to ultra-violet rays of the sun may cause chalking; however, should this occur, use of a mild furniture wax will remove residue and restore the original luster.
This option eliminates the stainless steel trap enclosure, which is normally provided standard to conceal valve assembly and P-trap. Typically, specification of this option would be in conjunction with the use of deck mounted faucets.
This option is available only with Straight Front Stainless Steel Washbasins. It provides raised front and side countertop marine edges for prevention of personal care products from rolling off of countertop.
This option provides lavatory or basin bowl with an overflow opening with connection to the waste outlet.
This option provides an individual deck mounted pump dispenser for each basin (Meridian) or every other station (Wash-Ware). Dispenser features anti-rotation pin to maintain discharge nozzle over basin. Option includes a reservoir featuring a separate refill. Not available for Corterra Kurve washbasins model number: 3791, 3792 and 3793.
This option provides an individual D shape basin, and is less the standard valve. It is intended to provide space on countertop to allow for use of a deck mounted faucet. This option must be used in conjunction with the -09 Less Spout and Valves option and requires the specification of the required VALVE PUNCHING. For 3700 series models, this option is a drop-in basin. For 3700IB and 3710 series models, this option is an integral basin. For 3770 series models, this option is a molded-in basin
This option provides a single 1-5/16" Diameter punching for spout and valve by others.
This option provides two 1-5/16" Diameter punching with 4" centers for spout and valve by others.
This option provides three 1-5/16" diameter punchings with 4" centers for spout and valve by others.
This option provides three 1-5/16" diameter punchings with 8" centers for spout and valve by others.
This option provides a sloping, straight front enclosure for 3700 series -1 Off-Floor Straight Front Stainless Washbasins and is provided standard with -2 On-Floor Straight Front Stainless Steel Washbasins. This option is NOT available for Curved Front Washbasins. Enclosure conceals valve, waste piping and bottom of unit. Enclosure frame is fabricated from heavy gage, type 304 stainless steel. Enclosure panels are fabricated from black vinyl clad, galvanized steel standard. Vinyl clad panels are optionally available in gray, white (-VP) or stainless steel (-SPX).
This option is intended to replace the standard vinyl clad enclosure with a stainless steel enclosure which includes a #4 satin finish.
This option provides a 2-1/2" high narrow front apron for Stainless Steel Washbasins. It is intended as an alternative to the standard 5" high apron and is best used when a specific look is desired. This option is NOT available in conjunction with options -SES Scalloped Enclosure Style, -SLE Sloped Front Enclosure, or -EB Enclosed Bottom. AVAILABLE only on -1 Off -Floor Models.
This option provides a Single Temperature Air-Control™ Metering Valve assembly and is offered as an alternative to the standard hot and cold mixing valve when a single water supply is desired.
This option provides a large trapezoidal shaped basin 17-1/4" wide x 12" wide x 11- 3/4" linear depth x 5-1/2" deep.
This option specifies a black vinyl clad enclosure. Black vinyl is standard for Stainless Steel Wash-Ware Washfountains and Meridian Wash Basin Models 3711, 3712, 3713, 3714.
This option specifies a gray vinyl clad enclosure. Gray vinyl is standard for Meridian Wash Basin Models 3771, 3772 and 3773.