Should we keep showing the banner you just clicked on?
Learn More about this warning
Learn More on Ligature-Resistant Fixtures
The LR1449 Comby design includes hemispherical features. These features reduce the risk of the fixture being used as a ligature device. Fixture shall be fabricated from type 304 stainless steel. Construction shall be seamless welded and exposed surfaces shall have a satin finish. Provide 47 3/8" long stainless steel grab bar with ADA compliant closure plate located behind toilet. Fixture optionally supplied with an Air-Control pneumatically operated, metering, non-hold open pushbutton valve. Valve shall require less than 5 lbs. to activate. Valve and bubbler conform with the requirements of NSF61, section 9 and is IAPMO R&T certified to meet the lead free requirements of Section 1417 of the Federal Safe Drinking Water Act and Section 116875 of the California Health and Safety Code. Toilet bowl housing is engineered to reduce risk of bowl being used as a ligature device. Toilet shall be concealed blowout jet type with an elongated bowl, a self-draining flushing rim, and an integral contoured seat. Fixture shall be cUPC certified and toilet shall meet ASME A112.19.3 and CSA B45.4 requirements and will flush with a minimum of 25 PSI flow pressure . Toilet trap shall have a minimum 3-1/2" seal that shall pass a 2-1/8" diameter ball and be fully enclosed. Cabinet interior is to be sound deadened with fire-resistant material. Fixture shall withstand loadings of 5,000 pounds without permanent damage. Fixture shall be furnished with necessary fasteners for proper installation.
The following item(s) have been added to your cart...You can now continue shopping or go
straight to checkout
This single temperature valve is a pneumatically operated, pushbutton valve that uses atmospheric air. The pushbutton is vandal-resistant and requires less than 5 pounds to activate valve. Valve can be remotely located up to 10 feet from the actuating button and is ideally suited for small chase areas. Metering provides an adjustable timed cycle flow from the valve. Timing is adjustable from 5 to 60 seconds. Air-Control™ features non-hold open pushbutton activation, and is provided with a stainless steel strainer and an integral checkstop. Valve conforms with the lead-free requirements of NSF61, Section 9, 1997; CHSC 116875 and ADA requirements.
This hot and cold valve is a pneumatically operated, hand pushbutton, soft closing valve that uses atmospheric air. The pushbutton is vandal-resistant and requires less than 5 pounds to activate valve. Valve can be remotely located up to 10 feet from the actuating button and is ideally suited for small chase areas. Metering provides an adjustable timed cycle flow from the valve. Timing is adjustable from 5 to 60 seconds. Air-Control features non-hold open pushbutton activation, and is provided with a stainless steel strainer and an integral checkstop. Valve conforms with the leadfreerequirements of NSF61, Section 9, 1997; Federal Public Law 111-380 and ADA requirements.
Learn more about electric water management
9VDC Programmable Piezo button(s) with 10’ foot connection leads are operated by touching piezo cap to activate solenoid valve. Button(s) have a default 8 second metered flow, but can be programed for additional time on site. Flow cycle can be stopped by touching the Piezo cap before the flow cycle ends. Button(s) are powered by 9VDC transformer or optional 6 AA battery pack (Batteries Not Included).
Toilet design that works utilizing 1.28 gallons (4.85 liters) per flush, thereby reducing water consumption.
Toilet/Urinal flush valves can be opted out as it would be supplied by others and not by Acorn.
This option is for the flush valve to be activated by a hydraulic pushbutton. This option is ADA compliant to be activated by 5 pounds of force or less. This is only available as a concealed flush valve (typically for toilet with a rear or wall supply configuration).
This option is to have the trim installed at the Acorn Engineering factory. The trim includes pushbutton(s), Bubbler, Spout, etc. This option saves time on installation in the field.
This option provides a recessed toilet paper holder which accommodates standard sized rolls. The holder is fabricated out of stainless steel and is welded into the body of the fixture.Indicate location.
This option provides unit housing with 12 gage (0.109") thick stainless steel in lieu of standard. This option is available only for Security Fixtures
With this specification, the inlet consists of a slip joint O-ring connection and permits a plus or minus 1/2" horizontal adjustment. The outlet is 4" no-hub.
With this specification, the inlet consists of a slip joint O-ring connection and permits a plus or minus 1/2" horizontal adjustment. The outlet is 3" no-hub.
Please note assemby does not include tee. This option provides a 6" stainless steel four prong hook in the cleanout. Hook is connected to 31" steel wire rope and is connected to a 4" brass plug with a 4-1/2" bolt. Plug to bolt connection is water tight.
This unique Acorn anti-flood system prevents toilet water overflow by shutting off the water supply from the flush valve. A reset button in the chase area reactivates the system only after the waste line has been cleared.
This option eliminates the requirement to manually reset the Flood-trol valve assembly by substituting a float tank for the reset button assembly. Flush valve becomes operable automatically after the flood condition has been corrected.
For use where wall thickness exceeds 2", this option allows the slip joint nut to be more accessible, making installation easier. The outlets at each end are NPT male threaded. Flush valve must be specified separately.
This option provides a flange which will accommodate a wax or rubber seal ring This is a standard feature on floor outlet and front access (Suffix Option -FA) models but must be specified on other models.
This option only available for use with optional Cleanout with O-ring (-CO1). This brass plug has a permanent stainless steel pin which extends downward to prevent large objects from passing through the waste piping. It is ideal for preventing mainline stoppages.
This option provides standard 2-3/8" O.D. Toilet bowl P-trap and includes an integral 3" O.D. plain end outlet connection that extends 3" beyond the rear of the fixture. This option will not alter the fixture flush valve rating or waste outlet rough-in location and still allows for passage of 2-1/8” diameter ball.
Option -BRS Brass Valve Body & checkstop assembly are pneumatically operated, pushbutton valves that use atmospheric air. The pushbutton is vandal-resistant and requires less than 5 pounds to activate valve. Valve can be remotely located up to 10 feet from the actuating button and is ideally suited for small chase areas. Air-Control valves are provided with a stainless steel strainer, a brass integral checkstop and conforms with the lead-free requirements of NSF61, Section 9, 1997; Federal Public Law 111-380 and ADA requirements. The -BRS Brass Valve Body option is also available with the 24V solenoid operated valves.
This options allows you to get the fixture without a punching for a flush valve. Typically, this option is used for units with remote activation.
This option provides a full size, 16 gage galvanized steel template to aid in the rough-in of fixtures. Only one template required per job.
This galvanized steel sleeve provides an opening in the wall for fixture mounting and becomes an integral part of the wall. The sleeve is typical useful in a rear mount/chase application.
Sister company Acorn Vac supplies means to evacuate plumbing waste through a vacuum system. The interface of atmospheric pressure at the toilet bowl and a constant vacuum pressure in the waste piping network provides a highly efficient flush, using only half gallon (1.89 liter) of water. When the push button is activated, the Extraction Valve opens, allowing atmospheric pressure to push toilet waste into the vacuum piping and toward the vacuum center. A water valve is simultaneously activated, allowing the toilet to be rinsed and refilled.
Valve assemblies can be manifolded to serve up to four fixtures from a single supply inlet. The valve assembly can be remotely located up to 10 feet away from the actuation pushbuttons. Two Single Temperature valves or two sets of Hot & Cold valves are manifolded. Option is available on Acorn Air-Control™ Valves or valves utilizing Master-Trol or Time-Trol.
This option is for the electronic valve system, namely Master-Trol and Time-Trol. The system is 24 VAC and this transformer is hardwired. Transformer is mounted to plate that fits junction box to cover connections.